When the nut is tightened on the compression fitting, it exerts pressure on the olive and bites it onto the pipe. This creates a watertight and airtight seal. Compression fittings are ideal for use in high pressure situations, like hot and cold water, oil, gas and petroleum lines.

What are plumbing olives made of?

An olive is a small metal ring, typically made from copper, brass or steel, and used in plumbing to create a seal in compression fittings.

What are nylon olives?

A nylon olive compression fitting is composed of an outer compression nut, and an inner compression ring or ferrule, which they call an ‘olive’. In this particular fitting, the olive is nylon. … With a nylon olive you don’t have to tighten the nut as much for an effective seal.

Can you use nylon olives on gas?

Clause 3.2. 3 (c) of the Gas Installation Code AG 601 prohibits the use of an “olive-type fitting”. Kinco compression fittings are considered such a fitting and cannot be used on Natural Gas or LP Gas installations. Gas fitters should only use approved fittings for the connection of gas appliances and equipment.

Which plumbing olives are best?

Copper olives are softer than the brass and will have a better seal when it is hot because it expands more slowly, especially when used on copper pipes which mean that there could also be less chance for leakage to occur during use.

Do you use brass olives with chrome pipe?

I use brass olives for things like chrome pipe, the olive has to bite into the pipe as well as seal against it and some may argue copper is too soft to bite into the chrome. Copper olives on plastic pipe/electric shower inlets etc.

Is it OK to use brass olives on copper pipe?

Copper olives are preferable to brass olives when using compression fittings with plastic pipe. I always use brass olives with copper pipes even if the fitting comes with copper olives.

Can I use compression fittings for natural gas?

Compression fittings in a gas piping system are not permitted unless allowed by the authority having jurisdiction. All tube fittings for natural gas installations are rated at more than 125 psig, but should not be used at pressures beyond those allowed by local codes.

What are copper olives used for?

Olives are ideally suitable for use with compression joints and copper or plastic pipe. Supplied in either copper or brass the olive fits directly to the intended connecting end of the pipe. When compressed the olive forms an air and watertight seal that will hold the pipe securely within the grip of the joint.

Are brass compression fittings suitable for gas?

Compression fittings can be used on gas pipes, although this should be left to a professional who is CORGI registered. Compression fittings can also be used to join a piece of copper pipe to a piece of plastic pipe as long as a soft (copper) olive is used instead of a brass olive on the plastic side.

Article first time published on

What is a Kinko nut?

Description. Kinko nuts and olives allow you to cut and join copper pipe without the need to solder the joins. They are used in conjunction with brass nipples as a compression fitting. The nut is screwed onto the nipple which compresses the olive and this forms a water tight seal on the pipe.

What is a plumbing Olive?

Olives, also known as ferrules, are used in compression fittings to help create a water tight seal. They sit on the pipe in between the compression nut and the main fitting body. … The olive remains inside and as the nut is tightened it grips the pipe to create a water tight seal.

Can you use brass olives on plastic pipe?

Compression fittings with short tube stop depth or hard olives should not be used with plastic fittings or pipe. … The connection should not need more than 2 full turns after the olive has gripped the pipe. Copper olives are preferable to brass olives. Ensure nut and olive are in place before inserting pipe insert.

Can you reuse olives?

Copper and brass olives both work fine. Olives can’t be removed from a pipe and reused. … If the protruding length of pipe beyond the olive is too long for the new fitting, no amount of tightening will make a sound joint.

Can you use copper olives on gas?

A compression fitting is the most commonly used joint when fitting out a boat gas system. They use an olive which is compressed to make the gas tight joint. … When making compression joints, Calor recommends the use of soft copper olives . These olives are easier to compress and therefore easier to produce a good seal.

How do you get an olive out of a plastic pipe?

Use a junior hacksaw to cut the olive at about 45 degree cut and go carefully so not to cut into the plastic pipe or your hands. It isn’t easy and blade will mark plastic badly if it slips. Flat blade screwdriver with thin blade to split the olive and always replace with copper olives.

Should you use PTFE tape on olives?

there is no need to put PTFE tape on a olive as it is the olive which causes the fitting to be sealed Tight.

Should you use Teflon tape on compression fittings?

NEVER! Do not use tape on compression or flare threads or union joints. No water touches those threads. Tape could keep the fitting from tightening properly.

Can I use SmarteX for hot water?

The red colour makes this pipe ideal for hot water identification. SmarteX-P PEX pipe offers an easy plumbing solution for residential or commercial applications. Simply push pipe into fitting for a secure fit.

Can I use PEX pipe for natural gas?

Yes you can, but because the terms PE and PEX have so often been used interchangeably it’s important to specify your intended use before purchasing polyethylene pipe for your project.

Can you use water compression fittings on gas?

Yes compression are perfectly suitable for gas.

Can you use compression fittings on central heating pipes?

Hi Compression fitting will be fine. Trades men often use them especially when a little water is present.

What is the most common cause of leaking compression fittings?

Over tightening is the most common cause of a leaking compression fitting.

Are copper compression fittings reliable?

Although compression fittings are generally considered more reliable than threaded fittings, there are some potential problems. In general, compression fittings are not as resistant to vibration as soldered or welded fittings. Repeated bending may cause the ferrule to lose its grip on the tube.

Can you reuse compression fittings?

Reusable Compression Fittings: They are safe to be reused and apply to half the movement of the pipe outward from the fitting. In hydraulic process, compression fittings basically assure some secure fit in pipe connections. Leaks are only possible if they are not properly installed to each end of the fluid line .

What happens if you over tighten a compression fitting?

If proper tightening procedures aren’t followed, it’s possible for tubing or fittings to become deformed. … This, in turn, will constrict flow and thin the wall of the tubing. Subsequently, this increase of local pressure and weakening of the tubing will cause compression fittings to catastrophically release the tubing.

Can you use copper push fit on gas?

2 Answers from MyBuilder Plumbers Hi Joe from my builder do not use these fittings on a gas supply only solder fittings or compression fittings hope this helps .

What is copper tubing used for?

Copper tubing is most often used for heating systems and as a refrigerant line in HVAC systems. Copper tubing is slowly being replaced by PEX tubing in hot and cold water applications. There are two basic types of copper tubing, soft copper and rigid copper.

What kind of olives do you use for plastic pipes?

Reasons why brass is a bit better is because on heating or hot water pipes, the seal will fail slightly as copper olives are softer. Also brass is better to redo the joint. Copper olives obviously needs to be used on plastic pipes.

Do compression fittings work on plastic pipe?

Compression fittings on plastic pipe A compression fitting works in the same way on a plastic pipe as it does on a copper pipe except that you need to put in a liner, which is there to keep the end of the pipe perfectly round.

Can compression fittings be used on poly pipe?

Yes, but only if they are compatible. Compression fittings with a short tube stop depth should not be used. Use a ‘TSM’ insert and follow the instructions of the compression fitting manufacturer when connecting to plastic pipework.