you can use your wrench to loosen the bolts that hold the bunks brackets in place on your boat trailer. Start at the most forward point of the bunk, raise the bunk until it touches the bottom of your boat and tighten until the bunk is in place.

How do you adjust the bunks on a boat trailer?

you can use your wrench to loosen the bolts that hold the bunks brackets in place on your boat trailer. Start at the most forward point of the bunk, raise the bunk until it touches the bottom of your boat and tighten until the bunk is in place.

How long should my boat trailer bunks be?

Ideally, the bunk boards should be at least half as long as your boat and run from the stern (or a few inches beyond it) to the bow as far forward as you like.

How is a boat supposed to sit on a trailer?

Set boat on trailer while maintaining no less than 2″ gap between keel and tongue plate cover. The end of the bunks/rollers should be flush with transom and the boweye should reach the winch post. If this is so, the rear pivot should remain in the A-position.

Should boat bunks be level?

1. The general rule of thumb is to adjust either rollers or bunks as low as possible and still keep the boat free of fenders and or the road. In particular the stern bunk adjustment normally will always be lower than the bow bunk adjustment.

Should trailer bunks be loose?

Possible to move them with strong effort, but generally you want the bunk boards to retain the hull angles when the hull is off the trailer. While you are down there, make sure the other bolts holding the wood bunks to the brackets are properly snug.

How do you adjust boat bunks?

1. Check your boat’s keel.
2. Adjust the keel rollers.
3. Adjust the front boat bunk brackets.
4. Adjust the rear boat bunk brackets.
5. Check your boat again.

How do you get a boat straight on a trailer?

1. Tie up your boat to the dock.
2. Then attach a single long line to the bow and stern cleat.
3. Back the trailer down deep enough that you can float the boat most of the way onto the trailer.
4. Using the line you can control the boat as you walk down the dock.

Where should you attach a self centering roller on a boat trailer?

In regards to installation, these will need to be installed towards the stern of the boat, in the center of the trailer. This would be the only place that would allow them to effectively center your boat on the trailer.

Is the front roller on my boat trailer supposed to be touching the keel when it's on the trailer?

In the full forward position on the trailer, the boat rest on the two boards. … It does indeed look like you need to move your keel rollers up towards the bottom of the boat until they are touching but not supporting the full weight.

Article first time published on

How long should bunks be?

The general rule of thumb is that you want your bunks to extend completely to the stern (rear) of the boat, or even and inch or two beyond. That way the transom has plenty of support as you drive down the road.

What kind of wood should be used for boat trailer bunks?

For wood, pressure-treated pine is the industry standard for trailer bunks. Popular alternatives are oak, cypress and other hardwoods that add even more durability. Composite boards used for patio decking are other options, but pressure-treated pine is a proven material with economic benefits.

Should a boat sit level on a trailer?

Your boat trailer should always be as level as possible when towing. Any time you’re towing anything, you should aim to have your trailer as level as possible. This is because you want the weight of your boat to be evenly distributed across the axles of your trailer.

How tall should boat trailer guides be?

Guide posts are L-shaped and available in different widths and heights. Most are 40″ to 60″ high. They are simple to install—just attach them to the trailer frame with brackets and bolts provided, and set them between the uprights a distance about 2″ wider than the widest beam of the boat.

Should boat trailer bunks move?

Jetboaters Captain. @Bdog is correct. You want them to move a bit so the boat can settle onto them fully each time. If you tighten them down too much and they don’t give, then you run the risk of the boat sitting on only a portion of the bunk and creating a larger opportunity for a wear in the gelcoat.

How should a jet ski sit on a trailer?

The jet ski should always sit on the trailer in a centered position as it has to be balanced on the trailer. Also make sure to pull it up completely until the bow reaches the bow stop and attach the safety chain!

How tight should boat guides be?

But since guide-ons are not meant to support weight like a regular bunk you don’t want it so close that the boat could damage the system, but they have to be close enough to help guide the boat on accurately. If it is as rough as it sounds like then I would say maybe 3 inches on each side would work.

How do you align boat trailer rollers?

Jack each wobble roller up (Starting from the back) until it is touching the hull of the boat but not taking the weight. Make sure you check both sides of the roller arm to ensure that both rollers are touching evenly on both sides). Back off the keel rollers approximately 1/4 to 1/2 a turn on the height bolts.

What is a self centering keel roller?

The Self-Centering Style Roller is designed to assist you in loading the boat onto the trailer, to help give you that extra push and line up your boat. … fastened into a Boat Trailer Roller Bracket by a Boat Trailer Roller Shaft.

Where should your trailer be located while you prepare to launch your vessel?

Turn off the engine and close all windows, ports, doors, and other openings. Where should your trailer be located while you prepare to launch your vessel? Well away from the boat ramp.

How far should you back your boat trailer into the water?

It should be just about as deep as it was when taking the boat off, and in most cases, about two-thirds of the trailer will be submerged while one-third remains out of the water. Don’t submerge the trailer too deep, or the bow of the boat may float over the bunks and go off to the side.

How do you put a boat on a bunk trailer?

1. Back the trailer in so the bunks get wet completely. …
2. Pull forward to a point where roughly a third of the center bunks are out of the water.
3. Nose the bow of the boat between the bunks.
4. Winch forward until the bow eye is up against the bow rollers. …
5. Slowly pull the boat out of the water.

How much overhang can you have on a boat trailer?

Note that on boat trailers the length of the front load carrying area is often difficult to define, so the maximum allowable rear overhang of 3.7 metres will normally apply.

What are strakes on a boat?

On a vessel’s hull, a strake is a longitudinal course of planking or plating which runs from the boat’s stempost (at the bows) to the sternpost or transom (at the rear).

How do you make a boat slide trailer easier?

Use a silicone spray such as (WD-40 Water Resistant Silicone Lubricant). This way is very effective and your boat will slide off the bunks fast. Make sure to have a rope or something to hold the boat from getting away from you.

Should my trailer be level when towing?

When towing, trailers should be level to improve stability, braking performance, and ground clearance. A level trailer will prevent poor towing characteristics, like sway, and uneven tire wear. … Adjusting the trailer to be level is important for safety.

What causes a boat trailer to sway?

Trailer sway can be caused by gusts of wind, or the passing of big rigs, but can also be caused by a multitude of things that you can fix yourself. 1. Not enough tongue weight–10 to 12 percent of the trailer’s weight must be on the tongue (where it hitches to your vehicle).

How do trailer guides work?

Trailer guide-ons attach to each side of a trailer. Guide-ons are normally put towards the rear of the trailer but can be mounted in other locations. To load the boat with guide-ons one person backs the trailer into the water. Another person drives the boat onto the trailer.

What size trailer do you need for a 22 ft boat?

Typically, a single-axle trailer can accommodate a boat up to 22′ (6.7 m) or 23′ (7.01 m) with a maximum weight of 3,300 lbs.