Reader’s Digest recommends mixing two parts baking soda to one part hydrogen peroxide to form a thick paste. Apply this paste in a targeted manner to any stains remaining in your tub. Allow the mixture to dry out fully, which should take around 30 minutes; then rinse with warm water.

How do I get my bathtub shine back?

Put the shine back in your porcelain sinks and bathtubs by giving them a good scrubbing with full-strength white vinegar, followed by a rinse of clean cold water. To remove hard-water stains from your tub, pour in 3 cups white vinegar under running hot tap water.

Can you buff an acrylic bathtub?

Because acrylic bathtubs are a solid surface, the color is the same throughout the entire acrylic sheet. … If your bathtub should happen to scratch or dull, you can easily restore the appearance back to new. Scratches and dulling can be removed with a liquid polisher such as Gel-Gloss or metal polish.

How do you buff a porcelain tub?

Baking soda is mildly abrasive and it can be used to polish small scratches in fiberglass or porcelain bathtubs. To use it, combine enough water with baking soda to make a thick paste. Rub the paste into the bathtub to remove the scratches. Rinse the bathtub with clean water when you are finished.

How do you clean a badly stained bathtub?

Combine 2 parts vinegar and 1 part water in a spray bottle and spray the entire bathtub. Allow this soaking solution to sit in the tub for 15-20 minutes. For tough stains: place a towel soaked in a vinegar and baking soda paste or hydrogen peroxide onto the stain(s) and allow the towel to sit for up to 1-hour.

How do you make an old porcelain tub look new?

Soak a non-abrasive sponge in the baking soda/ammonia solution and scrub the surface of your porcelain bathtub or sink, paying particular attention to stained areas. Dip the sponge in the solution, scrub and repeat until you’re satisfied.

How do I make my bathtub sparkle?

1. 1) Prevent soap scum and mildew from forming. …
2. 2) Experiment with DIY cleaners. …
3. 3) Scrub properly. …
4. 4) Pick the right tools. …
5. 5) Buy a showerhead filter. …
6. 6) Properly ventilate your bathroom. …
7. 7) Unclog your drain regularly.

Can porcelain tub be polished?

Keep a porcelain tub shiny with regular polishing. … The look of a porcelain tub can quickly go from vintage chic to old and shabby if the tub is not properly maintained and polished. With the right cleaning products and a little elbow grease, you can get your porcelain tub looking perfectly bright and shiny.

How can I make my old bathtub look new?

1. Sprinkle baking soda on stains.
2. Spray with warm water.
3. Leave 10-20 minutes.
4. Scrub with Mr. Clean Magic Eraser or soft sponge.
5. Rinse.
6. Dry with a soft microfiber cloth.

Can you use rubbing compound on fiberglass tub?

Apply a marine-grade rubbing compound with a soft cloth. Working in small sections, apply the compound onto the sides of your tub, paying special attention to dull spots and scratches. Do not focus on one area for too long. The compound may burn the fiberglass if you do.

Article first time published on

Can you use magic eraser on fiberglass tub?

You can clean your fiberglass bathtub with the help of a shower or cleaner mixture as explained in the steps below: … Rinse the fiberglass bathtub with the help of cold water and wipe away the excess water with the help of a paper towel. Now you can use a magic eraser to wipe away all the stains and dirt once again.

How do I make my dull acrylic tub shine?

1. Squirt 1/4 tsp. …
2. Drench a cleaning rag with the dishwashing solution. …
3. Continue wiping the tub’s surface with the solution until all buildup and stains are gone. …
4. Saturate another rag with water. …
5. Buff the tub’s surface with a soft towel. …
6. Inspect the tub for shine.

Is my tub acrylic or fiberglass?

Look around the tub’s edges and see if it appears thinner; this could be an indication that it is acrylic. Acrylic tubs usually come in more colors than fiberglass tubs, as fiberglass tubs are commonly white. Acrylic also feels warmer to the touch than fiberglass, and tubs made of acrylic have smoother finishes.

How do you make a dull fiberglass tub shine?

Sprinkle baking soda onto the tub’s surfaces and use the wet sponge to scrub it in gently. The combination of the vinegar’s cleaning and disinfecting properties, along with the mild abrasiveness of the baking soda, will clean your tub thoroughly and bring it back to a shine.

How do you whiten an old bathtub?

Mix ½ cup bleach into about a gallon of water. Using a sponge, coat the tub’s surface with the bleach and water solution and wait 5 minutes. After 5 minutes, scrub the surface with the sponge, paying special attention to the tougher stains. Rinse the tub with cold water, being careful not to splash the bleach.

Why is there black stuff in my bathtub?

Black specks may be caused by iron and/or manganese in the water system. These minerals are not harmful to humans or animals, but they give your household water an un aesthetic appearance, as well as possibly staining plumbing fixture and your ” clean” laundry or dishes.

Can bleach damage a bathtub?

Bleach is highly corrosive, so it’s always important to use it with caution. … A white bathtub can benefit from the occasional bleach treatment, but always use it in moderation. Simply pouring undiluted bleach directly onto the bathtub surface may cause the porcelain or other material to become permanently discolored.

What is the fastest way to clean a dirty bathtub?

Sprinkle baking soda on all tub surfaces. For extra-dirty tubs, use tub-and-tile cleaner instead. Fill your bucket with a half-gallon of hot water and two tablespoons of dish soap. Dip a scrub sponge or a stiff nylon brush into the bucket, and scrub all bathtub surfaces.

What cleans a porcelain bathtub?

1. Mix a gallon of hot water with a few tablespoons of dishwashing soap.
2. Use a cloth or sponge to scrub the tub’s entire surface.
3. Rinse well and repeat a week later. You may also want to polish your tub with a little lemon essential oil, rubbed all over with a soft cloth.

How can I make my bathtub look better?

Diluted bleach is particularly effective at combating mold and mildew growth in your tub. If you have dirty tiles around the tub, ordinary hydrogen peroxide is an effective tile and grout cleaner, and white vinegar is good for cleaning bathtub fixtures.

Is Bathtub Refinishing worth it?

Bathtub refinishing is worth the money if your tub is in good working condition. The reglazing process can remove surface imperfections, like scratches, shallow cracks, and stains. But if your tub is old, leaking, or full of mold, reglazing is just a waste of money. You’ll have to buy a new tub soon anyway.

Does bathtub paint work?

Wait, can you paint a bathtub? You can refresh your ceramic, porcelain, or fiberglass tub’s color and still achieve a high-gloss finish using a specialty kit labeled for tubs and tiles, often available at home centers for about $25.

Is my tub enamel or porcelain?

At first glance, you won’t be able to tell a porcelain bathtub from its enamel counterpart. But there’s a simple item you can use to determine bathtub types in this situation: a magnet. Since enamel tubs cover cast iron or steel, they’ll be magnetic. So if the magnet doesn’t stick, you have a porcelain tub.

Can you use car wax on a fiberglass tub?

The Dos and Don’ts of Polishing a Fiberglass Shower or Tub Wax on the floor of a tub or shower is dangerous!! It becomes a slip hazard leading to serious injury or death. So just don’t… … Any other liquid wax can also be used such as Turtle Wax or any automotive wax.

How do you get scratches out of a fiberglass tub?

Apply a small amount of polishing compound to a soft cloth if the petroleum jelly fails to remove the scratch. Rub the compound into the scratch in a circular motion. Rub your finger over the scratch to assess your progress. Repeat this process several times, or until the scratch disappears.

Can you use nail polish remover on fiberglass tub?

There are several products you can use to clean fiberglass, including acetone–a chemical that is also used to remove nail polish and other paints. Acetone removes not only dirt and grime from your fiberglass surfaces, but also any set-in stains like rust and pen marks.

How can I make my fiberglass tub look new again?

For weekly cleanings, pour 1 cup of water, 1 cup of vinegar and 1 tablespoon of dish soap into a spray bottle. Spray this right on the fiberglass surfaces and allow it to sit for at least 15 minutes. Scrub gently with a nonabrasive sponge and rinse with clean water.

Will Magic Eraser damage bathtub?

In general, if you have an acrylic tub, it’s best to use non-abrasive cleaners such as dish soap, Clorox wipes, or a mixture of vinegar and water. Do not try bleach or abrasive cleaners like steel wool on the tub. However, the Magic Eraser from Mr. Clean® is a safe option as long as you are gentle when scrubbing.

What is the best cleaner for fiberglass bathtubs?

Our top choice is Weiman tub tile & fiberglass cleaner. It is a powerful fiberglass cleaner that instantly removes tough stains, hard water spots, soap scum, limescale & rust without hard scrubbing. With the help of this non-abrasive formula, you can restore the natural color and texture of the fiberglass surface.

How do I know if my bathtub is fiberglass or plastic?

Looking closely at the edges of your tub, thin edges could mean fiberglass, while thicker edges could indicate acrylic. Another tip to rule out cast iron as a material, hold a magnet to the side and see if it sticks. If it does not stick, you most likely have either fiberglass or acrylic.

How do you tell if your tub is porcelain or acrylic?

Understanding Your Tub But how to tell the difference!?! Acrylic is pretty easy: If it looks plasticky, it’s an acrylic tub. If not, a simple test can help you to determine whether your tub is made of enamel or porcelain: put a magnet on it. If it sticks, the tub is enameled metal; if not, it’s porcelain.