Pipe wrench.Chain wrench.Socket wrench.Torque wrench.Ratcheting Wrench.Oil Filter Wrench.Combination wrench.Adjustable wrench.

What are the different wrenches called?

American nameBritish/Commonwealth nameGroupbox-end wrenchring spannercommoncombination wrenchcombination spanner open-ring spannercommonflare-nut wrench tube wrench line wrenchflare spanner flare nut spanner brake spanner crow’s-foot spannercommonratcheting box wrenchratcheting ring spannercommon

What are the three styles of wrenches?

Both of these have the same purpose. Moreover, there are three types of wrenches, which are socket, key, and spanner. A socket wrench can be a standard part of your toolbox. It can be inserted into a socket either vertically or horizontally to turn the bolt.

What are the most common wrenches?

Most common are the 1/4-inch, 3/8-inch and ½-inch ratchet drivers, but ¾-inch and 1-inch sets are available for heavy-duty work.

What are the different types of socket wrenches?

• #1) Ratcheting. Ratching is the most common type of socket wrench. …
• #2) Flex Head. There are flex-head socket wrenches that have a swiveling head. …
• #3) T-Handle. One of the most basic types of socket wrenches is the T-handle. …
• #4) Nut Driver. Another type of socket wrench is nut driver. …
• #5) Gearless.

What does a wrench look like?

A crescent wrench looks a lot like a monkey wrench; in fact, most of the simple adjustable wrenches you know look like crescent wrenches. A crescent wrench is usually made of steel and has a relatively flat handle that’s a number of inches long. … In contrast, a monkey wrench’s jaws are perpendicular to the handle.

What are the big wrenches called?

Hex Key/Allen Wrench.

How many wrenches are in a set?

A small set may have six to 10 wrenches, ranging in size from perhaps five-sixteenths to one inch. Standard wrenches are sold in sixteenth-inch increments up to one and a half inches (and in metric sizes, too, of course).

What order do wrenches go in?

Standard Combination Wrenches (1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1) Metric Combination Wrenches (6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Standard Flare Nut Wrenches (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 7/8) Note: Each wrench may combine two sizes.

What is open end wrench?

Definition of open end wrench : a wrench with jaws having a fixed width of opening at one or both ends of the handle.

Article first time published on

What is spud wrench?

Spud wrenches have a tapered spike at the handle end that’s used to align bolt holes when installing automotive components, beams, girders, or pipe fittings. The opposite end comes with a wrench to rotate fasteners for installation or removal.

What are all the socket sizes?

3/8″ Drive1/4″ Drive1/2″ Drive13mm10mm16mm14mm11mm17mm15mm12mm18mm16mm13mm19mm

What are the different socket sizes?

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters).

What are socket bits?

Socket bits are a combination of a bit, such as a screwdriver bit, and a hex socket. Socket bits connect to a turning tool such as a ratchet in the same manner as a hex socket, using a square drive socket. … One piece socket bits are more commonly found for use with impact wrenches.

How many types of spanners are there?

Millimeter spanners are available in variation 7mm similarly inch spanners are available in 1/16 and double-ended and ring spanners are mostly in sets of 6, 8, 12, and 36. In a set of 6 spanners in inch spanners, the double-ended and ring spanners are available in the following sizes.

What is a crows foot tool?

Crowfoot wrenches are open-end sockets that come in handy when reaching around obstacles. They work where common 6pt and 12pt sockets and wrenches simply cannot fit. … The crowfoot wrench above is shown attached to a ratchet with a short extension for extra reach.

What is the difference between a spanner and a wrench?

A spanner is a type of wrench with an opening and sometimes little teeth: you can clasp it over the nut or bolt and get a good grip. In the US, the main difference between a spanner and other wrenches is the spanner is adjustable and works with many sizes of nuts and bolts.

What are box end wrenches for?

A box, or closed, end wrench is used where there is room to place the wrench mouth around the fastener. Box end wrenches are available in 6- and 12-point versions to match the number of sides on the fastener. Hexagon fasteners have 6 sides, or points, and are the most popular. Open end.

How do I know what size wrench I need?

Take the diameter of the bolt, and multiply by 1.5. This calculation and conversion factor is valid for either metric or standard bolt sizes. The resulting number will be the size of the wrench you need to adjust the bolt properly. For example, If your bolt measures .

Are wrenches oversized?

RE: Bolt Hex vs Wrench Size The wrench is oversize relative to the nominal dimension, and the hex (bolt head) tolerance ranges from “right on” nominal to slightly undersized. For the 3/8″ hex example, the wrench opening (flat-to-flat dimension) is 0.378 to 0.384.

What size is smaller than 7 16?

Bolt DiameterMetricStandard1/8″8mm5/16″3/16″10mm3/8″1/4″11mm7/16″5/16″13mm1/2″

What size is a 17 wrench?

InchesMillimetersSpanner0.6005/16 Wworth; 3/8 BSF0.6255/8 AF0.63016mm16mm0.66917mm17mm

How big is the largest wrench?

30” Adjustable WrenchCheater WrenchCost$434.11$129.37Length30 inches15 inches

What is a wrench flat?

Consider adding wrench flats to the design of your lead screw. … When designed correctly, the flats will still allow a nut to travel over them and will serve as a a great way to keep the screw from rotating while you assemble your machine.

How does a wrench work?

Basically, a wrench consists of a stout lever with a notch at one or both ends for gripping the bolt or nut in such a way that it can be twisted by a pull on the wrench at right angles to the axes of the lever and the bolt or nut.

What is combination spanner?

Combination spanners are double-ended tools. It has an open-ended profile on one end and a closed loop on the other end. The two heads are usually at a 15 degree angle to the shaft for better access to the nuts or bolts. This single tool serves the functions of two spanners at once.

What does SAE stand for in wrenches?

SAE stands for Society of Automotive Engineers. This form of measurement was used primarily on cars made in the USA. This is why more often than not if you’re in the United States, you’re most likely finding wrenches and sockets in SAE sizings. AE sockets are sized in inches and fractions of inches.

What is a socket used for?

A socket attaches to a turning tool to tighten or loosen fasteners, such as a nut or bolt. Sockets are typically sold in sets with a drive tool. Sockets are tools used to tighten mechanical fasteners. They fit over the head of the fastener to provide torque.

What is the largest crescent wrench?

Overall Length30.0 in.762.0 mmWeight12.17 lbs.5520.22 g

What is a construction wrench?

Definition of construction wrench : an open-end wrench used by steel construction workers and having a long handle tapering to a blunt point that is used to hold matching holes (as for bolts or rivets) in alignment.

What is a hammer wrench?

Striking and slugging wrenches are short, thick wrenches that have a block shape on the end of the handle, intended for use with a hammer. With the wrench on a fastener, the block end is struck with a hammer to either tighten or loosen the fastener.