The high limit switch is a furnace component that controls elements of operation and safeguards the system. This component is connected to the blower motor as well as the gas valve and consists of a probe that detects temperatures mounted to a metal plate.

How do I know if my high limit switch is bad?

One of the most common issues that happens when a high limit switch goes bad is that it fails to signal the blower fan to turn off. If your fan keeps running continuously (and you’ve checked that your thermostat is set to AUTO rather than ON), that could be a sign of a bad high limit switch.

What trips a high limit switch?

A high limit switch will keep tripping due to a dirty flame sensor, short cycling, obstructed airflow, or a defective switch. These lead to overheating within the gas furnace that triggers tripping as a safety measure to prevent fires.

What happens if limit switch is bad?

One common symptom of a malfunctioning limit switch is a blower fan that doesn’t shut off. … A bad switch also can prevent a furnace from operating at all. If the switch has completely failed and is stuck in the open circuit (off) position, the furnace won’t run. The same effect can result from repeated overheating.

How do you reset a high limit switch?

1. Locate your furnace’s heating duct. …
2. Locate the white limit switch. …
3. Look at each arm to identify the settings. …
4. Identify the component (setting) located in between the two arms. …
5. Set the temperature on the middle component to approximately 105 to 115 degrees Fahrenheit.

Can you jump a limit switch?

It’s a standard procedure for problems to be solved. Two wires are going to the limit switch if you locate it. Take the wires away from the limit switch. For testing, jump the limit switch and tape the two terminals together.

Why does my limit switch keep tripping?

If the air inside your furnace gets too hot, the limit switch trips to prevent overheating. If the furnace high limit switch trips due to overheating, there is likely an airflow issue that is preventing proper air movement through the system. … A dirty filter is the most common cause of airflow issues.

How do I know if my limit switch is bad on my furnace?

The most common sign of a malfunctioning limit switch is the continuous operation of your furnace’s blower. Just as the limit switch won’t allow the fan to turn on until the warm air has reached the right temperature, the limit switch also shuts down when the air cools to a certain temperature.

How much does it cost to replace a limit switch on a furnace?

Average Cost of a New Furnace Limit Switch Depending on who your OEM is, this component could roughly cost you anywhere from $4 to $25.

How long does furnace flame last?

With all that being said, if there are no extreme factors involved, the average run time for a furnace is 10-15 minutes per cycle. Your furnace may need to run two to three times an hour to maintain your desired temperature if your home has average insulation.

Article first time published on

What causes a furnace to go out on high limit?

Dirty air filters are a common cause of furnace cycling problems. Air filters trap dust, dirt and debris. With time, the filter becomes clogged and restricts airflow to the equipment’s heat exchanger. When this happens, the heat exchanger overheats, forcing the high-limit switch to trip and the furnace to cycle off.

What does a high limit switch do on a hot tub?

Your hot tub high limit switch is designed to deactivate the heater when the water in your spa hits extreme numbers, often somewhere around 120° F. It’s a safety feature that will both protect any potential bathers in addition to your sensitive hot tub equipment.

What does open high limit mean on a furnace?

If the furnace failure code indicates an “open limit” or “open high temperature switch” or “open rollout switch”, it is probable that the furnace has overheated. Limit switches turn off the burner and turn on the circulating fan if there is a high temperature condition in the furnace. Play. Pause.

What is a limit switch and how does it work?

A limit switch is an electromechanical device operated by a physical force applied to it by an object. Limit switches are used to detect the presence or absence of an object. These switches were originally used to define the limit of travel of an object, and as a result, they were named Limit Switch.

How do you bypass a high limit switch on a spa?

The High Limit Switch Needs to Be Reset or Replaced Occasionally, the high limit switch will trip when you’re filling your spa. Or it might need a reset from time to time for no known or serious reason. Simply reset by pressing the big red button on your spa pack.

What should a limit switch read?

The fan limit switch should be open when the furnace is off and full of cool air, so you should get an OL reading; if not, there’s a short, and the switch should be replaced. The high limit switch should be closed when the furnace is cold, so you should get a zero reading; if you get the opposite, replace the switch.

What is a limit switch on a furnace?

A furnace limit switch is a component of a forced-air furnace that is responsible for turning on the furnace blower once the desired heat has been met inside the furnace. Without a functioning furnace limit switch, a furnace would not be able to regulate the temperature in conjunction with a thermostat.

How long should a furnace run daily?

Energy Savings Most systems should run about 2-3 cycles per hour. How long should the furnace or AC run in a given cycle? Typically 10-15 minutes in mild weather. The closer you get to the max design temperature in heating (0 Degrees) or cooling (90 Degrees) the longer the run cycle will be.

Why does my furnace not stay running?

Probably the most common issue when dealing with a furnace that will not stay lit or ignite consistently is a dirty flame sensor. The flame sensor acts as a communication vehicle with the circuit board and tells it when a flame is lit inside the furnace.

How do you reset a furnace after overheating?

1. Turn down the thermostat to its lowest setting.
2. At the circuit breaker, turn off the power to the furnace.
3. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on.
4. If the pilot light was out, light a match to relight it.

What causes a hot tub to overheat?

What Causes a Spa to Overheat? Low water flow (LF, FLO), is the usual cause of an overheating (OH, OHH) spa or hot tub. When water doesn’t flow fast enough through the heater, the heater stays hotter, and the temperature of the water increases. … Low water level in spa, and skimmer is sucking air.

Why is my hot tub hotter than setting?

Be aware that your hot tub may still register a few degrees higher than your setting due to the warmer, ambient outdoor temperature. Another common cause of summertime overheating is the filter cycle duration settings may be set too high. … This heat transfers into the tub water, increasing the temperature.

How do I fix the HL in my hot tub?

1. Turn the power off at the breaker for 15 seconds and then flip it back on. This will reset the HL reading.
2. You will notice the display show some numbers. …
3. If you see the HL come back within a day or so, this means that there is likely a problem with the probe or the motherboard.

What does a limit switch do on a golf cart?

The E-Z-GO Limit Switch is used on 21-current E-Z-GO Gas Vehicles as a mechanical device that enables the operation of the forward and reverse directions of the vehicle.

Is limit switch a sensor?

Limit switches are a type of sensor that detect presence and absence. Specifically, mechanical limit switches are switches that are mechanically activated, meaning that they have some sort of arm, lever, knob, plunger, etc., which is physically—or mechanically—activated by making contact with another object.

What is the function of a limit switch on a scissor lift?

Limit switches are usually used for setting upper travel or lower travel limits. If an intermediate position is needed an additional limit switch can be used. This limit switch is usually set up for actuating at the desired location coming from one direction only, either going up or coming down.