Unleaded gasoline with a minimum octane rating of 89 is recommended. A lower octane can cause some issues, such as increased engine temperature, increased piston seizures, and engine damage. Stihl offers 2-cycle oils made especially for Stihl chainsaws. Premium quality 2-cycle fuels provide protection for your engine.

What kind of gas do you put in a chainsaw?

The recommended gasoline in a Husqvaran chainsaw is regular unleaded gasoline. The engine needs a gasoline with an octane rating of 90 or higher for the it to run properly. The higher grade gasoline helps combustion in the cylinder and reduces the wear on the piston.

Do you mix oil with gas for chainsaw?

Read Your Manual Many gas-powered chainsaws run on a 40:1 mixture of gasoline and 2-cycle engine oil. Stihl chainsaws and others run on a 50:1 mixture of gas and 2-cycle engine oil. Some older models use a 30:1 ratio. … Oil cools the piston and cylinder to keep them evenly lubricated.

Do chainsaws take regular gas?

Nearly all gas chainsaws require a gasoline and oil mixture for their fuel. Chainsaw engines require a premixed fuel to keep them running at the proper temperatures. The oil that’s added to the fuel lubricates the piston and crankshaft, but it also keeps the engine cool enough to keep running.

How do you make a chainsaw fuel?

Gallons of GasolineFluid Ounces of Oil3 gal.7.68 oz.4 gal.10.24 oz.5 gal.12.8 oz.

What happens if you put straight gas in a 2 stroke?

Q: What would happen if you put regular unmixed gas in a 2 stroke engine? A: It soon seizes from lack of lubrication and becomes a NO stroke engine.

What kind of gas does a Stihl chainsaw use?

Using the right type of fuel is critical in the safe and efficient operation of your STIHL equipment. All STIHL gasoline-powered equipment runs on a 50:1 mixture of gasoline and 2-cycle engine oil. Knowing the proper way to mix your fuel is the first step in keeping it running strong and long.

How long can a chainsaw run on a tank of gas?

I find about 30 to 40 minutes of work is the most out of most saws. The tanks are not real big to keep them light and they use quite a bit of fuel at speed. Make sure to tighten the blade at least every refueling and refill the oil tank. Don’t use used motor oil as chain oil.

Can you put chainsaw gas in a car?

I have a leaf blower and a small chainsaw that operate on a gasoline-oil mixture. … Yes, you may pour the unused fuel mixture into your car, provided you don’t fill the tank with the stuff. A couple gallons, if diluted by a tank-full of gas, will do no harm.

Can you use car oil in a chainsaw?

You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30.

Article first time published on

How tight should a chainsaw chain be?

A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.

Is a chainsaw 2 or 4 stroke?

Most chainsaws have a two-cycle (also called two-stroke) motor. They have no sump oil, so you need to add lubricant to the gas or the motor will overheat and seize. It’s vital that you use the right ratio of oil to gas, so check your owner’s manual.

How much gas does a chainsaw use?

The general ratio for most two-stroke chain saw combustion engines is 50:1, though some manufacturers recommend 40:1. The larger number represents the amount of gasoline, while the smaller is the amount of oil needed.

What kind of gas does a Husqvarna lawn mower use?

What to buy and what to avoid… E10 can be used in all current Husqvarna equipment, however, we recommend using at least 89-octane E10 gasoline, which is the mid-grade between regular and premium gasoline.

What octane is premium gas?

Retail gasoline stations in the United States sell three main grades of gasoline based on the octane level: Regular (the lowest octane fuel–generally 87) Midgrade (the middle range octane fuel–generally 89–90) Premium (the highest octane fuel–generally 91–94)

Should I use premium gas in my Stihl chainsaw?

STIHL recommends that customers use a minimum of 89 octane fuel. If a customer chooses to use a 91 or 93 octane fuel, no damage to the engine will result. However, using an 87 octane fuel could lead to serious engine damage.

Can I use ethanol gas in my Stihl chainsaw?

STIHL products can use gasoline blends with up to 10% ethanol. It is important to follow proper fuel storage recommendations with all standard pump gasoline. Improper fuel storage is a leading cause of fuel system component failures which can lead to expensive engine damage.

What happens if you mix too much oil in a 2 stroke?

Using the proper oil-to-gas ratio is important, but if you’re off, it’s better to mix too much oil into your engine than mixing too little oil. Excess oil can produce a smoky exhaust, oil leaking out of the muffler, and sometimes loss of power.

What is special about 2 stroke oil?

A 2-stroke oil will lubricate the engine components by association with the fuel (either by mixing with it or by spraying during combustion), so this oil contains components that promote its combustion.

Can you use motor oil instead of 2 cycle oil?

Yes, you can. Use it in the same proportions you would use 2 stroke oil. The main point being to maintain the lubricating qualities of the oil added to the fuel, too little can cause bearing and bore damage.

Does mixing gas hurt engine?

Mixing grades is not going to do any harm to your car. If your vehicle requires 87 octane unleaded then there’s absolutely *no* advantage to using a higher octane gasoline. Period. You’re better to spend your fuel dollars on “top tier” gasoline than wasting it paying for octane your engine cannot use.

Will 2 stroke gas hurt my car?

Two stroke engines mix gas and oil to power up an automobile. … It is so to avoid the damage that might happen to the engine. Running a vehicle on two stroke fuel for a temporary basis will not harm at all. But make sure to clean and fill up the tank with straight specific fuel immediately.

What happens if you put 2 stroke gas in a 4 stroke engine?

You can run a 4 stroke motor with fuel youve mixed for a 2 stroke. You may have oil smoke from the exhaust or foul plugs over some time, but it wont hurt the engine. You cannot run diesel fuel in a gas engine or vice versa either.

Why does my chainsaw run hot?

Chainsaw engines run at high temperatures, usually in the summer, so they can quickly overheat. … If dust, wood chips or other material blocks these systems, the engine will start to overheat. The engine also needs to expel hot air, so the muffler must also be kept clean to keep the engine from overheating.

How often should a chainsaw be cleaned?

Routine maintenance, including cleaning, will both prolong a chainsaw’s life and give you better results. They don’t need to be cleaned after every use or anything like that, but perhaps after every 20 – 30 hours worth of work. It’s all going to depend on how often you use it.

How fast is a chainsaw?

The piston ring speed on the average chainsaw travels 2,500 surface feet per minute. A chain slides across the surface of the sawbar rail at around 5000 feet per minute. The chain is moving at 55 to 60 m.p.h. or a mile per minute ( 88 feet per second ).

What happens if you run a chainsaw without bar oil?

No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.

Can you use transmission fluid for chainsaw bar?

On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .

Can you use wd40 on a chainsaw?

We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.

How often should you change the bar on a chainsaw?

If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.

How often do you need to sharpen a chainsaw?

You can mount your sharpener if you use your chainsaw throughout the year as it makes it easy to sharpen the tool and also helps to avoid accidents. In most cases, sharpening the chain should happen after ten times of being in use, while in other situations, you have to sharpen it after every session.